A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
Just how do you feel about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't specifically rocket science, yet it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard task. If the old tub is easily obtainable, the task can relocate quickly; if you have to open up a wall to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will need an assistant to vacate the old tub and set in the new one. See to it you have actually certified on your own for the job and are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you begin. Possibilities are you may require a specialist plumber to make tube links.
This write-up will assist you mount a brand-new tub in your bathroom if you have actually already bought a new bathtub and also don't need to transform the plan of your previous supply of water pipelines.
Your tools and product checklist need to make up the following:
Getting ready for the Installation
First of all, the sustaining frame supplied with the bath needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps system to prevent strain on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its last placement.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of removing the existing faucets can be rather bothersome as a result of the restricted access that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. When the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to proceeding to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bathtub
Using both wood boards under its feet, place the bath tub in the called for position. The wood boards are valuable in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four small factors.
The following goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the bathtub till the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling and also sealing around the tub should wait until the bath tub has actually been made use of at the very least when as this will settle it into its last position.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers are in location in between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. Once the tap is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The former type should be attached to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break a rigid seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, causing complications with wetness and possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Remember to always load the bathtub with water prior to sealing, to permit the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or waterproof glue as well as grout.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
We were made aware of that editorial on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through someone on a different web blog. You should take the opportunity to promote this blog if you enjoyed it. I appreciate reading our article about How to Install a Bathtub Yourself.
Schedule An Appointment Report this page